QUESTION 81
When configuring port security on a Cisco Catalyst switch port, what is the default action taken by the switch if a violation occurs?

A.    protect (drop packets with unknown source addresses)
B.    restrict (increment SecurityViolation counter)
C.    shut down (access or trunk port)
D.    transition (the access port to a trunking port)

Answer: C

QUESTION 82
hostname Switch1
interface Vlan10
ip address 172.16.10.32 255.255.255.0
no ip redirects
standby 1 ip 172.16.10.110
standby 1 timers 1 5
standby 1 priority 130
hostname Switch2
interface Vlan10
آip address 172.16.10.33 255.255.255.0
no ip redirects
standby 1 ip 172.16.10.110
standby 1 timers 1 5
standby 1 priority 120
Refer to the above. HSRP was implemented and configured on two switches while scheduled network maintenance was performed.
After the two switches have finished rebooting, you notice via show commands that Switch2 is the HSRP active router. Which two items are the most likely cause of Switch1 not becoming the active router? (Choose two.)

A.    Booting has been delayed.
B.    The standby group number does not match the VLAN number.
C.    IP addressing is incorrect.
D.    Preemption is disabled.
E.    Standby timers are incorrect.
F.    IP redirect is disabled.

Answer: AD

QUESTION 83
Private VLANs can be configured as which three port types? (Choose three.)

A.    isolated
B.    protected
C.    private
D.    associated
E.    promiscuous
F.    community

Answer: AEF

QUESTION 84
Refer to the exhibit. Which statement about the private VLAN configuration is true?

A.    Only VLAN 503 will be the community PVLAN, because multiple community PVLANs are not allowed.
B.    Users of VLANs 501 and 503 will be able to communicate.
C.    VLAN 502 is a secondary VLAN.
D.    VLAN 502 will be a standalone VLAN, because it is not associated with any other VLANs.

Answer: C

QUESTION 85
When configuring a routed port on a Cisco multilayer switch, which configuration task is needed to enable that port to function as a routed port?

A.    Enable the switch to participate in routing updates from external devices with the router command in global configuration mode.
B.    Enter the no switchport command to disable Layer 2 functionality at the interface level.
C.    Each port participating in routing of Layer 3 packets must have an IP routing protocol assigned on a per-interface level.
D.    Routing is enabled by default on a multilayer switch, so the port can become a Layer 3 routing interface by assigning the appropriate IP address and subnet information.

Answer: B

QUESTION 86
You have configured a Cisco Catalyst switch to perform Layer 3 routing via an SVI and you have assigned that interface to VLAN 20. To check the status of the SVI, you issue the show interfaces vlan 20 command at the CLI prompt. You see from the output display that the interface is in an up/up state. What must be true in an SVI configuration to bring the VLAN and line protocol up?

A.    The port must be physically connected to another Layer 3 device.
B.    At least one port in VLAN 20 must be active.
C.    The Layer 3 routing protocol must be operational and receiving routing updates from neighboring peer devices.
D.    Because this is a virtual interface, the operational status is always in an "up/up" state.

Answer: B

QUESTION 87
Refer to the exhibit, which is from a Cisco Catalyst 3560 Series Switch.

Which statement about the Layer 3 routing functionality of the interface is true?

A.    The interface is configured correctly for Layer 3 routing capabilities.
B.    The interface needs an additional configuration entry to enable IP routing protocols.
C.    Since the interface is connected to a host device, the spanning-tree portfast command must be added to the interface.
D.    An SVI interface is needed to enable IP routing for network 192.20.135.0.

Answer: A

QUESTION 88
What is the result of entering the command "port-channel load-balance src-dst-ip" on an EtherChannel link?

A.    Packets are distributed across the ports in the channel based on the source and destination MAC addresses.
B.    Packets are distributed across the ports in the channel based on the source and destination IP addresses.
C.    Packets are balanced across the ports in the channel based first on the source MAC address, then on the destination MAC address, then on the IP address.
D.    Packets are distributed across the access ports in the channel based first on the source IP address and then on the destination IP addresses.

Answer: B

QUESTION 89
Which Cisco IOS command globally enables port-based authentication on a switch?

A.    aaa port-auth enable
B.    radius port-control enable
C.    dot1x system-auth-control
D.    switchport aaa-control enable

Answer: C

QUESTION 90
Which two steps are necessary to configure inter-VLAN routing between multilayer switches? (Choose two.)

A.    Configure a dynamic routing protocol.
B.    Configure SVI interfaces with IP addresses and subnet masks.
C.    Configure access ports with network addresses.
D.    Configure switch ports with the autostate exclude command.
E.    Document the MAC addresses of the switch ports.

Answer: AB

Passleader Real Cisco 642-813 PDF & VCE Exam Dumps For Free