A. The final active router is the router with IP address 172.16.11.111.
B. The router with IP address 172.16.11.111 has preempt configured.
C. The priority of the router with IP address 172.16.11.112 is preferred over the router with IP address 172.16.11.111.
D. The IP address 172.16.11.115 is the virtual HSRP IP address.
E. The router with IP address 172.16.11.112 has nonpreempt configured.
F. The router with IP address 172.16.11.112 is using default HSRP priority.
Which two statements about HSRP, VRRP, and GLBP are true? (Choose two.)
A. GLBP allows for router load balancing of traffic from a network segment without the different host IP configurations needed to achieve the same results with HSRP.
B. GLBP allows for router load balancing of traffic from a network segment by utilizing the creation of multiple standby groups.
C. GLBP and VRRP allow for MD5 authentication, whereas HSRP does not.
D. Unlike HSRP and VRRP, GLBP allows automatic selection and simultaneous use of multiple available gateways.
E. HSRP allows for multiple upstream active links being simultaneously used, whereas GLBP does not.
A. enables LACP unconditionally
B. enables PAgP only if a PAgP device is detected
C. enables PAgP unconditionally
D. enables EtherChannel only
E. enables LACP only if an LACP device is detected
Refer to the exhibit. Which two problems are the most likely cause of the exhibited output? (Choose two.)
A. spanning tree issues
B. HSRP misconfiguration
C. VRRP misconfiguration
D. physical layer issues
E. transport layer issues
A. Interface gigabitethernet 0/1 has been configured as Layer 3 ports.
B. Interface gigabitethernet 0/1 does not appear in the show vlan output because switchport is enabled.
C. Interface gigabitethernet 0/1 does not appear in the show vlan output because it is configured as a trunk interface.
D. VLAN2 has been configured as the native VLAN for the 802.1q trunk on interface gigabitethernet 0/1.
E. Traffic on VLAN 1 that is sent out gigabitethernet 0/1 will have an 802.1q header applied.
F. Traffic on VLAN 2 that is sent out gigabitethernet 0/1 will have an 802.1q header applied.
Refer to the exhibit and the partial configuration of switch SW_A and SW_B.
STP is configured on all switches in the network. SW_B receives this error message on the console port:
00:06:34: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/5 (not half duplex), with SW_A FastEthernet0/4 (half duplex), with TBA05071417(Cat6K-B) 0/4 (half duplex).
What is the possible outcome of the problem?
A. The root port on switch SW_A will automatically transition to full-duplex mode.
B. The root port on switch SW_B will fall back to full-duplex mode.
C. The interfaces between switches SW_A and SW_B will transition to a blocking state.
D. Interface Fa 0/6 on switch SW_B will transition to a forwarding state and create a bridging loop.
A. IP traffic matching access list ABC is forwarded through VLANs 5-10.
B. IP traffic matching VLAN list 5-10 is forwarded, and all other traffic is dropped.
C. All VLAN traffic matching VLAN list 5-10 is forwarded, and all traffic matching access list ABC is dropped.
D. All VLAN traffic in VLANs 5-10 that match access list ABC is forwarded, and all other traffic is dropped.
Which two statements about HSRP are true? (Choose two.)
A. Load sharing with HSRP is achieved by creating multiple subinterfaces on the HSRP routers.
B. Load sharing with HSRP is achieved by creating HSRP groups on the HSRP routers.
C. Routers configured for HSRP must belong only to one group per HSRP interface.
D. Routers configured for HSRP can belong to multiple groups and multiple VLANs.
E. All routers configured for HSRP load balancing must be configured with the same priority.
Which statement about 802.1x port-based authentication is true?
A. Hosts are required to have an 802.1x authentication client or utilize PPPoE.
B. Before transmitting data, an 802.1x host must determine the authorization state of the switch.
C. RADIUS is the only supported authentication server type.
D. If a host initiates the authentication process and does not receive a response, it assumes it is not authorized.
Refer to the exhibit. Switch S1 has been configured with the command spanning-tree mode rapid-pvst. Switch S3 has been configured with the command spanning-tree mode mst. Switch S2 is running the IEEE 802.1D instance of Spanning Tree. What is the result?
A. IEEE 802.1w and IEEE 802.1s are compatible. IEEE 802.1d is incompatible. Switches S1 and S3 can pass traffic between themselves. Neither can pass traffic to switch S2.
B. Switches S1, S2, and S3 can pass traffic between themselves.
C. Switches S1, S2, and S3 can pass traffic between themselves. However, if the topology is changed, switch S2 does not receive notification of the change.
D. IEEE 802.1d, IEEE 802.1w, and IEEE 802.1s are incompatible. All three switches must use the same standard or no traffic can pass between any of the switches.
Passleader Real Cisco 642-813 PDF & VCE Exam Dumps For Free